Learn what a belt sander is, why you need one, how to use, and the extensive benefits of this tool in an easy to follow guide.
Belt sanders are multiuse tools. They are commonly used for trimming to a scribed line (photo), sanding very rough surfaces, leveling surfaces (like a replacement board in a hardwood floor) and freehand rounding and shaping. Because they have a lot of power and can handle coarse grits, they excel at the rapid removal of wood. Also, unlike orbital and vibrating sanders, the sanding action is linear, so even with coarse grits you can sand with the grain and get a good-looking result. Though a belt sander isn’t an essential tool in the homeowner’s arsenal, you won’t find many experienced DIYers or carpenters without one.
Benefits of a belt sanderBelt sanders are the big, powerful gorillas of the sanding world. Few tools can save you as much time—or wreck your project faster. If you’re new to belt sanders or have been frustrated by yours, read on to find out how to keep that big ape under control.
Family Handyman
Perfect for scribingA common use for a small belt sander is scribing. You can gradually sneak up on a curved line for a perfect fit. On a laminate countertop, make sure the direction of belt travel pushes the laminate down.
Family Handyman
The Top Tool for Rough FlatteningBelt sanders excel at the rapid removal of wood, making them the best handheld power tool for leveling and smoothing rough boards. Start at an angle to the grain for aggressive leveling, then finish with the grain. 80-grit is good for starting, then switch to 120-grit.
Family Handyman
How to Choose the Best Belt SanderThe best multipurpose belt sander takes a 3-in.-wide belt. You’ll see machines designed for wider and narrower belts, but they’re for specialized tasks.
Personally, I use 80- and 120-grit belts regularly, and rarely, 50-grit. Grits coarser than 50 leave deep scratches that are difficult to remove. And if you’re doing finer sanding, you’re better off using a random-orbit sander. Remember one of the rules of sanding: You can skip one grade of grit, but it wastes time and you’ll just wear out belts skipping two. For example, you can go from 80 to 120, skipping 100 grit, but don’t go from 50 to 120.
Aluminum oxide is the traditional grit material. You’ll find it in less expensive khaki-color form, good if you need a disposable belt, and longer-lasting, dark brown premium belts. However, for grits of 80 and coarser, many people now prefer zirconia belts (sometimes called “planer” belts). They have sharper, tougher cutting particles that cut more aggressively, last longer and don’t clog as easily. These belts are usually bright blue or purple. Zirconia belts cost slightly more than premium aluminum oxide belts.
Family Handyman
How to Use a Belt SanderDon’t push down on the sander; let its weight do the work. Go slowly, overlap passes and allow the tool to go past the end without dipping. Be careful not to tip the sander or change speed or direction. Put the cord over your shoulder so it’s out of the way.
Family Handyman
Watch Out for GougingThis painted panel shows a common problem: horseshoe-shaped gouges at the end of a board. To prevent gouges, use clean, new belts, avoid grits finer than 120, and keep the plate under the belt (the platen) clean and free of dust buildup.
Belt sander safety tipsBelt sanders are relatively safe tools, but it’s still smart to take precautions.
Family Handyman
Trim After SandingIt’s hard to keep a belt sander from gouging or rounding over the ends of a board. So if you can, belt-sand the board before cutting it to final length. You can then safely move on to a palm sander and finer grits.
Family Handyman
Watch Out on PlywoodBelt sanders take off serious amounts of wood, so they can wreck plywood pretty much instantly. If you have to sand solid-wood edging flush with plywood, draw a pencil line on the plywood to tell you when the sander starts removing veneer. If you have variable speed, dial it down.
Belt sander maintenanceFirst, make sure the belt is oriented properly. Some belts have a preferred direction, indicated by an arrow on the inside. Nondirectional belts can be installed either way. The only adjustment you’ll probably have to make is “tracking” to keep the belt centered on the roller. Hold the sander up, turn it on, and see if the belt either rubs against the housing or starts working its way off the rollers. With the trigger on, adjust the tracking knob until the belt is centered on the rollers. You may have to make a slight adjustment when the sander is on the wood. If your sander has automatic tracking, you don’t need to mess with any of that nonsense.
Some sanders have variable speed. You can go at maximum speed most of the time, but you’ll want to throttle it back for delicate work.
Family Handyman
Keep the Belt CleanDirty belts make for lousy work. A belt-cleaning stick will remove the pitch buildup that happens with all woods, especially pine or sappy woods. Push it against the moving belt, or for larger sanders, clamp the stick in a vise and sand it.
Family Handyman
Good for Rough SharpeningYou can use a belt sander for rough sharpening of tools like axes, shovels, knives and chisels. Remove the dust bag and remove all dust from the sander (sparks and dust are a bad combination), then use a zirconia belt for best results.
Family Handyman
Upgrade your sanderBelt sanders are simple tools that don’t need many improvements. However, if you use your belt sander in the shop, consider these two upgrades.
Dust collectionBelt sanders always come with a built-in dust bag that collects most of the coarser dust and needs regular emptying. However, plenty of fine dust still gets into the air. If you’re doing a lot of belt sanding, it’s worth getting a hose that allows you to connect your sander to a shop vacuum. You’ll be able to sand all day with nary a speck of dust (lower photo).
You can sometimes use the hose that came with your shop vacuum, but it’s usually too large or too stiff. The alternative is a super-flexible, small-diameter hose designed for dust collection. You can buy one at a woodworking specialty store or online (search “vacuum hose”). I use one made by Porter-Cable that cost $25. Dust ports vary widely (some are square, which is a challenge), so you may have to fiddle around to get the hose to fit. There are commercial adapters ($10 to $20; pick one up when you buy your hose) or you can cobble something together with—you guessed it—duct tape. It’s worth the fuss, though: no dust in your workspace.
Shop-made standA handy accessory if you do much woodworking is a stand that holds your sander on its side, upside down or vertical, allowing you to bring the work to the tool instead of vice versa. The design of the stand is completely dependent on the shape of your sander, so we won’t give plans. However, it generally involves several layers of plywood, each with cutouts to accommodate the parts of the sander that protrude, plus a couple of hose clamps or other clamping devices to hold the sander securely. Add another piece of plywood to act as a table, if needed.
Stands like this are particularly useful if you want to sand lots of small parts—for example, if you’re making lots of wooden toys. For inspiration, search online for “belt sander stand photo.”